Kibata

Sign In

Our Services

Get 15% Discount on your First Order

Order Now
[rank_math_breadcrumb]

Lab111

Lab – Using IOS CLI with Switch MAC Address Tables

Lab – Viewing the Switch MAC Address Table

Topology

Addressing Table

Device

Interface

IP Address

Subnet Mask

Default Gateway

S1

VLAN 1

192.168.1.11

255.255.255.0

N/A

S2

VLAN 1

192.168.1.12

255.255.255.0

N/A

PC-A

NIC

192.168.1.3

255.255.255.0

N/A

PC-B

NIC

192.168.1.2

255.255.255.0

N/A

Objectives

Part 1: Build and Configure the Network

Part 2: Examine the Switch MAC Address Table

Background / Scenario

The purpose of a Layer 2 LAN switch is to deliver Ethernet frames to host devices on the local network. The switch records host MAC addresses that are visible on the network, and maps those MAC addresses to its own Ethernet switch ports. This process is called building the MAC address table. When a switch receives a frame from a PC, it examines the frame’s source and destination MAC addresses. The source MAC address is recorded and mapped to the switch port from which it arrived. Then the destination MAC address is looked up in the MAC address table. If the destination MAC address is a known address, then the frame is forwarded out of the corresponding switch port associated with that MAC address. If the MAC address is unknown, then the frame is broadcasted out of all switch ports, except the one from which it came. It is important to observe and understand the function of a switch and how it delivers data on the network. The way a switch operates has implications for network administrators whose job it is to ensure secure and consistent network communication.

Switches are used to interconnect and deliver information to computers on local area networks. Switches deliver Ethernet frames to host devices identified by network interface card MAC addresses.

In Part 1, you will build a multi-switch topology with a trunk linking the two switches. In Part 2, you will ping various devices and observe how the two switches build their MAC address tables.

Note: The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15.0(2) (lanbasek9 image). Other switches and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the labs.

Note: Make sure that the switches have been erased and have no startup configurations. If you are unsure contact your instructor.

Required Resources

2 Switches (Cisco 2960 with Cisco IOS Release 15.0(2) lanbasek9 image or comparable)

2 PCs (Windows 7 or 8 with terminal emulation program, such as Tera Term)

Console cables to configure the Cisco IOS devices via the console ports

Ethernet cables as shown in the topology

Note: The Fast Ethernet interfaces on Cisco 2960 switches are autosensing and an Ethernet straight-through cable may be used between switches S1 and S2. If using another model Cisco switch, it may be necessary to use an Ethernet crossover cable.

Build and Configure the Network

Cable the network according to the topology.

Configure PC hosts.

Initialize and reload switches as necessary.

Switch#delete flash:vlan.dat

Switch#erase startup-config

Switch#reload

Configure basic settings for each switch.

Configure device name as shown in the topology.

Configure IP address as listed in Addressing Table.

Assign
cisco as the console and vty passwords.

Assign
class as the privileged EXEC password.

Switch(config)#hostname S1

S1(config)#interface vlan 1

S1(config-if)#ip address 192.168.1.11 255.255.255.0

S1(config-if)#no shutdown

S1(config)#line console 0

S1(config-line)#password cisco

S1(config-line)#login

S1(config-line)#line vty 0 15

S1(config-line)#pass cisco

S1(config-line)#login

S1(config-line)#exit

S1(config)#enable secret class

Examine the Switch MAC Address Table

A switch learns MAC addresses and builds the MAC address table, as network devices initiate communication on the network.

Record network device MAC addresses.

Open a command prompt on PC-A and PC-B and type
ipconfig /all. What are the Ethernet adapter physical addresses?

PC-A MAC Address: __The MAC address in this example is 00-50-56-B3-27-D6._________________________________________________________________

PC-B MAC Address: __________The MAC address in this example is 00-50-56-B3-FF-54._________________________________________________________

Console into switch S1 and S2 and type the
show interface F0/1 command on each switch. On the second line of command output, what is the hardware addresses (or burned-in address [bia])?

S1 Fast Ethernet 0/1 MAC Address: _____S1F0/1_________________________________________________

S2 Fast Ethernet 0/1 MAC Address: _____0cd9.96d2.3f81._________________________________________________

	S1# show interface f0/1

FastEthernet0/1 is up, line protocol is up (connected)

Hardware is Fast Ethernet, address is 001a.e3cf.b883 (bia 001a.e3cf.b883)

MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,

<output omitted>

S2# show interface f0/1

FastEthernet0/1 is up, line protocol is up (connected)

Hardware is Fast Ethernet, address is 0025.83e6.9081 (bia 0025.83e6.9081)

MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,

<output omitted>

Display the switch MAC address table.

Console into switch S2 and view the MAC address table, both before and after running network communication tests with ping.

Establish a console connection to S2 and enter privileged EXEC mode.

In privileged EXEC mode, type the
show mac address-table command and press Enter.

S2#
show mac address-table

Even though there has been no network communication initiated across the network (i.e., no use of ping), it is possible that the switch has learned MAC addresses from its connection to the PC and the other switch.

Are there any MAC addresses recorded in the MAC address table?

The switch may have one or more MAC addresses in its table, based on whether or not the students entered a ping command when configuring the network. The switch will most likely have learned MAC addresses through S1’s F0/1 switch port. The switch will record multiple MAC addresses of hosts learned through the connection to the other switch on F0/1

.

What MAC addresses are recorded in the table? To which switch ports are they mapped and to which devices do they belong? Ignore MAC addresses that are mapped to the CPU.

The MAC address table might contain several MAC addresses, particularly those acquired through the F0/1 switch port of S1. In the provided output example, the MAC address of S1’s F0/1 and PC-A are associated with S2’s F0/1.

If you had not previously recorded MAC addresses of network devices in Step 1, how could you tell which devices the MAC addresses belong to, using only the output from the
show mac address-table command? Does it work in all scenarios?

The result from executing the “show mac address-table” command indicates the port where the MAC address was discovered. Typically, this helps identify the network device associated with the MAC address, except when multiple MAC addresses are linked to a single port. This occurrence arises when switches are interconnected, recording all MAC addresses for devices connected to the interconnected switch.

Clear the S2 MAC address table and display the MAC address table again.

In privileged EXEC mode, type the
clear mac address-table dynamic command and press
Enter.

S2#
clear mac address-table dynamic

Quickly type the
show mac address-table command again. Does the MAC address table have any addresses in it for VLAN 1? Are there other MAC addresses listed?

Wait 10 seconds, type the
show mac address-table command, and press Enter. Are there new addresses in the MAC address table? __________________

No. The student will most likely discover that the MAC address for the other switch’s F0/1 switch port has been quickly reinserted in the MAC address table.

From PC-B, ping the devices on the network and observe the switch MAC address table.

From PC-B, open a command prompt and type
arp -a. Not including multicast or broadcast addresses, how many device IP-to-MAC address pairs have been learned by ARP?

The ARP cache may have no entries in it, or it may have the gateway IP address to MAC address mapping.

C:\Users\PC-B>
arp –a

Interface: 192.168.1.2 — 0x6

Internet Address Physical Address Type

192.168.1.255 ff-ff-ff-ff-ff-ff static

224.0.0.22 01-00-5e-00-00-16 static

224.0.0.252 01-00-5e-00-00-fc static

255.255.255.255 ff-ff-ff-ff-ff-ff static

From the PC-B command prompt, ping PC-A, S1, and S2. Did all devices have successful replies? If not, check your cabling and IP configurations. Yes

From a console connection to S2, enter the
show mac address-table command. Has the switch added additional MAC addresses to the MAC address table? If so, which addresses and devices?

There may only be one additional MAC address mapping added to the table, most likely the MAC address of PC-A.

From PC-B, open a command prompt and retype
arp -a. Does the PC-B ARP cache have additional entries for all network devices that were sent pings?

 ARP cache on PC-B should have more entries

Reflection

On Ethernet networks, data is delivered to devices by their MAC addresses. For this to happen, switches and PCs dynamically build ARP caches and MAC address tables. With only a few computers on the network this process seems fairly easy. What might be some of the challenges on larger networks?

On larger networks, the dynamic building of ARP caches and MAC address tables can pose several challenges.

1.
Increased Traffic: With a higher number of devices, there is more network traffic generated as devices communicate and broadcast ARP requests to discover each other’s MAC addresses. This can lead to increased network congestion.

2.
Table Size: As the network grows, the size of MAC address tables on switches and ARP caches on devices also increases. Managing and maintaining extensive tables becomes more complex and resource-intensive.

3.
Broadcast Storms: Larger networks are more susceptible to broadcast storms, where a broadcast message generates a high volume of traffic, potentially overwhelming the network and degrading performance.

4.
Address Resolution Delay: With a larger number of devices, the time taken for address resolution (mapping IP addresses to MAC addresses) may increase, leading to potential delays in communication.

© 2024 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page
1 of
10

© 2024 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page
5 of
10

image3.png

image4.png

image5.png

image6.png

image7.png

image1.png

image2.png

image8.jpeg

Share This Post

Email
WhatsApp
Facebook
Twitter
LinkedIn
Pinterest
Reddit

Order a Similar Paper and get 15% Discount on your First Order

Order Now

Related Questions

Computer Science 2 Assignments

Operational Excellence Week 2 Assignment Information Systems for Business and Beyond Questions: · Chapter 3 – study questions 1-8, Exercise 2, 4 & 5 Information Technology and Organizational Learning Assignment: Chapter 3 – Complete the two essay assignments noted below:  · Review the strategic integration section.  Note what strategic integration is and how

Discussion 3: generative adversarial nets

  Generative adversarial nets are mentioned in 2014 by Ian Goodfellow et al.  Why is generative adversarial network a key turning point in the history of generative modeling? Why is the field of image generation important? 

Week 3 – Linear Regression & Business Decision Making

attached file.  An asset management company must replace the manager of its two signature mutual funds, who is about to retire. Two candidates have been short-listed. The management team is divided and cannot decide which of the two candidates would make the better mutual fund manager. The retiring manager presents

data science

Final Exam Due Saturday 11:59 pm (Week 15) You cannot use any of the datasets in our assignments, class notes, and your own midterm project. If you are using the same one, you will receive 0 for your final project. 1. Question Formulation (5 points): You need to devise a

Letter of Recommendations

Hi  Attached is the sample of Letter of recommendation  Please write about it accordingly  1. Write about author :AUTHOR WILL BE professor David Kimble I will give links about his Biography write accordingly or you can use your own search engines about him to write it. 2 . How the

Letter of Recommendations

Hi  Attached is the sample of Letter of recommendation  Please write about it accordingly  1. Write about author :AUTHOR WILL BE professor David Kimble I will give links about his Biography write accordingly or you can use your own search engines about him to write it. 2 . How the

data science

Final Exam Due Saturday 11:59 pm (Week 15) You cannot use any of the datasets in our assignments, class notes, and your own midterm project. If you are using the same one, you will receive 0 for your final project. 1. Question Formulation (5 points): You need to devise a

IT 202

5/15/24, 10:59 AM Assignment Information 1/3 IT 202 Project One Milestone Guidelines and Rubric Overview For the purposes of this assignment, imagine that you are a systems architect at a medium-sized publishing company with 130 employees. The company primarily publishes books, both in print and online. It also produces other

Assessments

Perimeter defense techniques Evaluate the types of assessments, select one that you might use, and explain why it is important. Of the top eight areas to research when conducting an assessment, select no less than three and explain how one should approach the research and why it should be approached

project ppt presentation

Project 3 – Ensemble Methods and Unsupervised Learning In this project you will explore some techniques in unsupervised learning as well as ensemble methods. It is important to realize that understanding an algorithm or technique requires understanding how it behaves under a variety of circumstances. You will go through the

Week 2 understanding on Python.

PDF for reference purpose other file is requirement Python Installation & Examples Atif Farid Mohammad PhD 1. Open any Browser 2. Go to 3. Click at Download button 4. Go to your Download Folder (In both Windows and Mac) a. In Windows you will have the file: Anaconda3-2022.05-Windows-x86_64.exe b. Double

Computer Science Assignments

Operational Excellence Week 2 Assignment information Systems for Business and Beyond Questions · Chapter 2 – study questions 1-10, Exercise 2      Information Technology and Organizational Learning Questions · Chapter 2 – Note why the IT organizational structure is an important concept to understand.  Also, note the role of

Computer Science IT project assignment

Pg. 01 Project I Project Deadline: Sunday 12/5/2024 @ 23:59 [Total Mark is 14] Introduction to Database IT244 College of Computing and Informatics Project Instructions · You can work on this project as a group (minimum 2 and maximum 3 students). Each group member must submit the project individually with

project ppt presentation

Project 3 – Ensemble Methods and Unsupervised Learning In this project you will explore some techniques in unsupervised learning as well as ensemble methods. It is important to realize that understanding an algorithm or technique requires understanding how it behaves under a variety of circumstances. You will go through the

coding

Assignment 6 Due Saturday 11:59 pm (Week 14) Part 1 (50 points) We will explore the Marvel Network Universe. The dataset which you will find in Blackboard consists of the hero’s networks. For this dataset, you will need to ask yourself 3 questions (i.e which superhero knows more superheroes?) ,

project ppt presentation

Project 3 – Ensemble Methods and Unsupervised Learning In this project you will explore some techniques in unsupervised learning as well as ensemble methods. It is important to realize that understanding an algorithm or technique requires understanding how it behaves under a variety of circumstances. You will go through the

How hackers get info

Identify at least two ways in which hackers gather information about companies. What can companies do to limit this access, specifically to the ways you have identified? Which type of information can be gathered with enumeration? How and why should companies protect themselves against enumeration attempts?